The Launch Pad Maverick AGM-65B Air-to-Ground Missile The Maverick AGM-65B is a scale model of the air-launched tactical missile. The real deal attacks small targets with a high-explosive charge for optimal effectiveness. This TLP model flies on a selection of 24mm mid-power rocket motors : D12-3, D12-5, E15-4, F24-7. When fully assembled, the Maverick kit is 21.5" long with a 2.6" airframe diameter. Skill level 3 model rocket.
		$23.99

Fliskits Saturn 1B 1:282 This is a 1:282 peanut scale model kit of the infamous Saturn 1B NASA vehicle. The NASA vehicle was used to test parts of the Apollo moon mission in the 60's. The finished Saturn 1B model is 9.316" tall and has a 0.976" diameter. It offers excellent levels of detail, often not seen in larger models. This scale model rocket kit has a unique feature. It lets you, the builder, decide what skill level the kit is. You can build it as a skill level 3 kit. If you need more of a challenge, you can make it a skill level 4, or even level 5 model. The instructions are written in a way that allows the modeler to set the skill level for this model rocket kit. You're in control. Recommended engines : 1/2A3-4T, A3-4T, A10-3T. These are the popular 13mm motors which enable the Fliskits Saturn 1B kit to enjoy many, cheap, flights. This Fliskits rocket kit includes a parachute, and silk-screened decals. While the kit includes a launch lug, the rocket can also be flown with a pop lug or piston launcher (neither are included). This is the same design that was used by Jay Marsh to secure a first place at the national NARAM rocketry event in the 90's.
	$23.95

		Fliskits Thunderbird This is a flying sport scale model of the Thunderbird anti-aircraft missile. It is approximately 1:14 scale, it is not an exact replica. The real missile was created by the British Army and was nicknamed the Bloodhound System. It was in use from the late 50's to the mid 70's. It was known to be a highly accurate and lethal weapons system. This rocket kit includes balsa fin stock with fin templates, and paterns to form the booster nose cones from paper. This Flis rocket kit is intended for more experienced modelers. The finished Fliskits Thunderbird is 27.48" tall and has a 1.637" diameter. Fin span is an impressive 7.62". Listed weight is 1.9 oz. Parachute include for safe recovery. Model rocket engines to use with this kit are : Estes B6-4 and Estes C6-5.
		$23.95

Dr Zooch Rockets Soyuz Proudly made in the USA, this model rocket kit is a scale replica of the Russian Soyuz spacecraft. The Dr Zooch Soyus kit comes with lots of little pieces to give it an excellent level of detail and realism. The finished Soviet model is a touch over 18" tall and weighs around 2.2oz. It flies on 18mm Estes or Quest A, B, and C model rocket engines. The Soyuz rocket kit includes a parachute for recovery.
	$23.95

		Dr Zooch Rockets Saturn V Lots of fun details to work with on the Saturn V kit, such as the fairings, engine nozzles, cable tunnels, ullage motors, and transitions. The Saturn V model rocket kit includes color decals to make it come to life. Fully assembled, it stands about 18" tall. This hobby rocket has a 18mm motor mount and can be flown on Estes or Quest A, B or C motors. A parachute is included to return the Saturn V to ground control.
		$23.95

Dr Zooch Rockets Saturn IB The Saturn IB includes lots of details, such as the full tanks, H1 engines, nozzle assembly, Apollo module, and escape tower. This Dr Zooch kit measures 17" tall when finished. The Saturn IB scale model has a 18mm motor mount, for B or C rocket engines. A parachute is included to help with safe returns to the launch site.
	$23.95

		Dr Zooch Rockets Mark II Unlikely the other Dr Zooch flying rocket kits, this isn't a scale model of an existing vehicle. It does have that unique space program look and feel. The Dr Zooch Mark II model rocket stands 12.2" tall and has a 2.93" fin span. Weight without motor should be around 2.4 oz. This is one of the easier-to-build Dr Zooch kits, so if you're looking for a first model kit with space program style, the Mark II may be just be a good first kit to buy. Complete with payload bay for cargo, the Mark II flies on 18mm motors, such as the Estes B6-4. Plastic parachute included for recovery.
		$23.95

Dr Zooch Rockets Jupiter C This is a scale model of the rocket used to launch the first US satellite, as part of the space race. The vehicle was known as the Explorer I, and the rocket was a slightly modified version of the Jupiter C, which some would call the Juno I. The completed Dr Zooch Jupiter C model rocket is about 12" tall. It is one of the easier Dr Zooch kits to build and a great overall flier. The Jupiter C kit is a single-stage flying model rocket which comes complete with balsa fin stock, pre-printed wraps, and plastic parachute. The shock cord setup is a combination of Kevlar and elastic. Recommended engines are Estes or Quest A, B or C. Flights to over 1,400 ft are possible with a C6-7.
	$23.95

		Dr Zooch Rockets Ares I-X The Ares I-X is one of the latest additions to the Dr Zooch family of scale space models. This is a scale model of NASA's test vehicle for a series of next-generation manned space vehicles. The finished model stand a little over 19" tall and weighs around 1.5 oz. The Dr Zooch Arex I-X flies on Estes-style B and C model rocket engines. Flights over 2,000 feet are possible. A plastic parachute is included for recovery. The yellow flames seen in the picture are actually fins which are needed for stable flight.
		$23.95

Dr Zooch Rockets Ares I Also known as "The Stick", the Ares I is a scale model of NASA's next-generation crew launch vehicle. This model is a good choice for a first Dr Zooch space program scale kit. The finished Ares I stands 19.5" tall. This model rocket kit includes printed wraps which minimize the amount of painting needed to make it look great. Build one of these manned spacecraft today and get it in the air before NASA gets a chance to fly theirs.
	$23.95

		Sunward Penguin Model Rocket Kit This fun rocket kit is BT80 based (2.6" diameter) and is 11 1/2" tall. The Sunward Penguin is a great stubby rocket. Includes 18" parachute, laser-cut balsa fins, lite-ply mounting rings, and a balsa nose cone. Skill level two kit. Who says penguins can't fly? This penguin rocket can put on quite the show with these engines : C11-3, C11-5, D12-3, D12-5, and D12-7.
		$22.49

The Launch Pad Dragonfly This skill level two model rocket is a Launch Pad original design, not one of their usual military scale kits. The Dragonfly still boasts the stylish looks of a missile and readily reports for duty on these Estes & Aerotech rocket motors : D12-3, D12-5, E15-7 & F24-7. The finished mid-power Dragonfly rocket is 26.5" long with a 1.6" body diameter (BT-60). An 18" Mylar parachute is included with the kit for recovery.
	$21.99

		The Launch Pad Lance MGM-52 Tactical Battlefield Missile As a successor of the Honest John, the Lance MGM-52 was capable of delivering a variety of payloads at high speed and with considerable precision. The Launch Pad Lance model rocket is a skill level 2 kit and measures 28.75" tall (2.6" diameter). It flies on these Estes and Aerotech 24mm motors : D12-5, D12-7, E15-7 & F24-4. The "U.S. Army" decal seen in the picture is not included with this model rocket kit.
		$21.99

Sunward Galactic Wave This galactic warrior is always on patrol and comes fully armed with laser cannons, ready for battle if needed. Recommended engines are the B6-2 for the maiden flight and C6-3 for more daring missions. This skill level 3 kit comes with parts including quality laser-cut balsa fins, an 18" parachute, rubber shock cord, silkscreen decals, and illustrated instructions in both English and French. When finished, the model boasts 22" in length, and has a 9" wingspan. The rocket's airframe diameter is 1.346". Build your own and send the Galatic Wave out on patrol at your next launch!
	$21.95

		ASP WAC Corporal This is a 1:9 scale model of the USA's first sounding rocket, the Wac Corporal. It was a liquid-fuel rocket and was first launched in 1945. Fly it on any of these model rocket engines for serious fun : Estes C11-5, D12-7, E9-6, E9-8, or Aerotech E15-7 and E30-7. With an adapter (not included) the WAC Corporal model rocket can also fly on the B4-2, B4-4, B6-4, and C6-5. That's a lot of motor choices for one kit. The finished kit measures 21.875" long, airframe diameter is 1.325", weight : 2.77 oz. Includes parachute for recovery.
		$21.95

Fliskits Nantucket Sound An original design and 24mm motors make the Fliskits Nantucket Sound a great additional to any rocket fleet. This odd-roc was originally designed to be a commemorative kit for the NARCON 2009 rocketry event. This flying lighthouse stands 9.316" tall with a 0.976" airframe diameter. The Fliskits face card shows the weight as 1.01 oz. Recommended engines are the Estes C11-3, D12-3, and for even more excitement, the E9-4. This makes for a great motor selection for the Nantucket Sound rocket kit. Note that it will deploy a bit late with the E9-4, use at your own risk. Plastic parachute included for recovery. A paper nose cone is used to keep this flying model rocket kit cheap enough for all to enjoy.
	$20.95

Fliskits Corona-2 Advanced-looking two stage model rocket design. A whopping 43.0" long (0.976" diameter). The package deal shown for sale here includes both booster and sustainer rocket stages. The impressive length of this skill level 3 kit increases stability for fantastic, extreme altitude flights. For the booster stage, a B6-0 or C6-0 can be used. For the sustainer, recommended model rocket motors are : A8-5, B6-6, and C6-7. The included parachute brings the Corona-2 back safely. Laser cut fins, detailed instructions, and the usual Fliskits quality parts make this a great kit. Can be flown in two stage or single stage configuration.
	$20.95

Squirrel Works Firebird SuperSonic Transport Ready for a sci-fi style adventure, the Firebird SuperSonic Transport cruises off on any of these model rocket motors : A6-4, A8-3, B4-4, B6-4, & C6-5. Inspired by SST concepts, this futuristic model is 21.0" tall with a 0.976" body diameter. It's sleek design give it that special appearance that stands out. Don't you wish you had a whole fleet of these? Some of the quality parts included in this Squirrel Works kit are : balsa nose cone, laser-cut fins, mylar parachute, water-slide decals.
	$19.95

		The Launch Pad Perseus Surface-to-Air Missile This flying model rocket kit is a The Launch Pad original design. It is not a scale model of an existing military device. If it were real, the Perseus would probably be an interceptor capable of taking down enemy aircraft or even inbound missiles. Recommended rocket engines for the Perseus are the D12-5 and D12-7. The rocket is 26.25" long (1.6" diameter). The "U.S. Navy" decal/lettering shown in the image is not included with this skill level 3 kit.
		$18.99

Squirrel Works Ajax Inspired by space-craft often found in comic books in the 1930's, the Ajax is a welcome blast from the past. The clever combinations of wings and fins really make this kit stand out. Water-slide decals are included to complete the overall look. Along with quality parts, the illustrated instructions assist the modeler when creating this retro sci-fi bird. Laser-cut balsa, Mylar parachute, balsa nose cone all included. The finished model measures 15.25" tall, has a 1.325" diameter with a 1.5 oz estimated weight. Watch out, the Ajax is going in 3, 2, 1 on a A8-3, B4-4, B6-4, or C6-5.
	$18.95

		Squirrel Works Vulture This space plane looks like it is up to no good. The name Vulture doesn't exactly scream "humanitarian missions" either! Pick one up for yourself today and make the call : peaceful explorer, or intergalactic evil-doer. This flying model rocket kit includes the usual Squirrel Works quality parts : laser-cut fins, balsa nose cone, Mylar parachute, detailed instructions, canopy template, water-slide decals. The futuristic Vulture is 13.403" long, with a 1.325" airframe diameter. Listed weight : 1.5 oz. Blast off on the mission of your choice with a A8-3, B4-4, B6-4, or C6-5 engine.
		$18.95

Fliskits Shadowlord Take but one look at this hobby rocket and you'll know the Fliskits Shadowlord is ready for major excitement. Fly the Shadowlord on a C11 for smaller fields, or go crazy with an F motor for serious fun and entertainment. If you're new to 24mm motors, this kit offers a great way to start slowly with a C11 and work your way up to an F24, when ready. All recommended rocket motors : Estes C11-5, D12-5, E9-6 and Aerotech D15-5, E15-6, F24-7. Requires a 3/16" launch rod, motors are friction-fit. Includes water-slide decals and parachute. This model rocket stands 24.12" tall, and has a 1.325" body tube diameter. Fin span : 7.32", weight : 2.62 oz.
	$18.95

		Fliskits Rose-A-Roc Based on the original design of Art Rose, this rocket can be used for 18mm helicopter duration competitions. Fliskits says this about the Rose-A-Roc : "One of the best HD models in the industry!". This model rocket measures 20.54" long and its diameter is 0.736". Quite the versatile flier, it performs well on these model rocket motors : 1/2A6-2, A8-3, B4-2, B6-4, and C6-5. Looking for something different? Give this model a try!
		$18.95

Edmonds Twinsee The Edmonds Twinsee model rocket kit includes two gliders. These are joined together for launch and separate when the ejection charge fires. Each aircraft glides down individually. Only one rocket engine is required per flight. Recommended motors are : B4-2, B4-4, and C6-5. Building this set of gliders only takes about two hours. A single Twinsee kit includes all parts, and enough balancing clay, needed to build two gliders.
	$18.95

		Squirrel Works Callisto The Callisto has a transition, which gives it that unique sixties-style space program look. Send this rocket off to explore with any of these Squirrel Works recommended engines : A6-4, A8-3, B6-4, B6-6, C6-5, or a C6-7. When fully assembled, the Callisto is 16 7/8" tall with a 1.325" diameter. The face-card lists the weight as 1.6 oz. This flying model rocket kit comes complete with a balsa transition, nose cone, and laser-cut fins. The kit includes a Mylar parachute for recovery. Also included are water-slide decals to help finish the model. Buy one today and add a classic-looking kit to your collection.
		$17.95

Starlight S.S. Barracuda This new Starlight rocketry kit is a fierce intergalactic space pirate. It hides in the emptiness of space, waiting to board and plunder any craft that crosses its path. Fly this space-worthy ship on an A8-3, B6-4 or a C6-5. She be 25" tall and 1.64" round, she be. The futurisctic S.S. Barracuda is outfitted with parachute and decals. Heave-To, Matey. Pick one up today, or these pirates may just have ye walk the plank!
	$16.95

		Squirrel Works Gremlin In three words : speed and power! Designed to be a performer, this model rocket can hit 1,500 feet on a D motor. With its 1.325" body tube diameter, the Gremlin prefers these model rocket engines : C11-5, C11-7, D12-5, D12-7. The completed vehicle is 15.35" long with a 1.6 oz estimated weight. Recovers with a Mylar streamer for closer landings. The fins are laser-cut, the nose cone is balsa. Complete with water-slide decals and illustrated instructions.
		$16.95

Fliskits Frick-n-Frack This is an excellent two-stage rocket for smaller fields. It stages at around 40-50 feet and the rocket stays under 100 feet during the entire flight. Before launch, it looks like a regular six-sided saucer on the launch pad. Once airborne it surprises onlookers as it stages. The included assembly jigs and detailed instructions help greatly with assembly of the saucers. Recommended model rocket engines are : B6-0 & C6-0. The Fliskits Frick-n-Frack is 5.5" long, has a 0.736" diameter with a 10.24" fin span.
	$16.95

		Fliskits HERC-5 Explore the galaxy in style aboard this futuristic recreational craft. Fliskits design at its best. If you like details, you'll love the full sheet of water decals to decorate this bird. Combined with this rocket's unique shape, they complete the Fliskits "Hobbicron Empire Recreational Craft 5". This futuristic model is nearly two feet tall (21.08") with a 0.736" diameter. Skill level 2 kit with a few fun challenges. The Fliskits HERC-5 isn't picky about motors either, a B4-2, B6-4, or C6-5 will do nicely.
		$16.95

Fliskits Deuce's Wild! One of the more popular Fliskits kits. If you've ever seen this model rocket fly, you already know why. It sports a two engine cluster design. The dual canted motor mounts make for an exciting and unique smoke trail. The Deuce's Wild! can be flown on two A8-3, or B6-4 motors. If you have a large enough launch field, go all out with 2 C6-5 motors. This is a skill level 3 kit and offers a great way to get into clustering. Parachute recovery. The Deuce's Wild stands 21.2" tall with a 1.637" diameter.
	$16.95

		The Launch Pad Bolo This is a Launch Pad design, not based on any actual missile. The TLP Bolo has all the style of an artillery rocket, capable of carrying an impressive warhead. As a skill level 2 kit, it is a great introduction to The Launch Pad for beginning modelers. The Bolo model rocket kit is 27.25" long with a 1.6" diameter (BT-60). It flies on a nice selection of 24mm motors, including the D12-3, D12-5, E15-7, E30-7, and RMS E18-7 & F24-7.
		$15.99

Squirrel Works Jarrod Frankum's High 5 This is the 3rd member of the Signature Series family of Squirrel Works flying model rocket kits. Originally designed by Jarod Frankum as part of the NSL 2006 rocketry event. The High 5 model rocket kit includes hand-shaped laser-cut fins, balsa nose cone, colorful waterslide decals, and a Mylar streamer for recovery. Recommended rocket motors are : A8-3, B4-4, B6-4, C6-5 The Jarrod Frankum's High 5 stands 14.45" tall, and has a 1.325" body diameter. Clearly a fun kit that will be an instant favorite for rocketeers of all ages. This flying model rocket kit is recommended for modelers age 10 and up, with adult supervision for those under age 12.
	$15.95

		Squirrel Works JX-1 This futuristic rocket kit sports beautiful retro sci-fi styling combined with high quality parts. The tubes on the fins and canards give it a unique look which will not go unnoticed. The nose cone, and the laser-cut fins & canards are balsa wood. The parachute is Mylar. Complete with water-slide decals. For adventures of various altitudes, this selection of rocket engines can be used : A6-4, A8-3, B6-4, C6-5. The JX-1 stands 13.875" on the launch page and the BT-50 tubing gives it a 0.976" body diameter. Squirrel Works lists the weight as 1.2 oz.
		$15.95

Fliskits Rhino Excellent kit for new modelers. Laser cut fins and detailed instructions make it a good first kit to build. Instructions for the Rhino model rocket kit even include hints and tips, specifically for beginners. This larger Flis model (24.5" long, 1.637" diameter, 10.5" fin span) makes for dramatic, slow takeoffs. Great for smaller launch fields. Flies on B4-2, B6-2, and C6-5. Balsa nose cone. Parachute recovery. Well suited for educational/classroom setting.
	$15.95