Adhesives / Glue

We stock adhesives, which you might need for all kind of rocketry projects. Browse this category or narrow your selection to a specific glue type or foam.

Wood/Paper/Plastic glue
Wood / Paper /
Plastic Glue
CA Glue
CA Glue
(Superglue)
Epoxy
Epoxy
Expanding Foam
Expanding
Foam
Threadlocker
Threadlocker
Back to Build Supplies
Back to Build
Supplies
   

30 Min Slow-Cure Epoxy 4.5 oz

30 Min Slow-Cure Epoxy 4.5 oz

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with...
$11.75

Add to Cart


30 Min Slow-Cure Epoxy 9 oz

30 Min Slow-Cure Epoxy 9 oz

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight. Fillers such as microballoons can be mixed with...
$19.25

Add to Cart


Plastic Cure. Gap-filling CA for Plastics

Plastic Cure. Gap-filling CA for Plastics

Plastic-Cure™ is a gap-filling formulation of CA that works best on plastics. It is packaged in a bottle with a brush built into its top, which in many cases is an easier way to apply the CA. As long as brush is put back into the bottle after use, the bristles of the brush will not harden....
$5.75

Add to Cart


Insta-Cure, Super Thin Cyanoacrylate 1/2 oz

Insta-Cure, Super Thin Cyanoacrylate 1/2 oz

Bob Smith INSTA-CURE has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off...
$5.50

Add to Cart


Insta-Cure+, Medium Cyanoacrylate 1/2 oz

Insta-Cure+, Medium Cyanoacrylate 1/2 oz

Bob Smith INSTA-CURE+ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting...
$5.50

Add to Cart


Maxi-Cure, Extra thick Cyanoacrylate 1/2 oz

Maxi-Cure, Extra thick Cyanoacrylate 1/2 oz

Bob Smith MAXI-CURE bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, cloth-textured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CURE or any other adhesive. It also is best...
$5.50

Add to Cart


IC-GEL

IC-GEL

This Gel is perfect for reinforcing existing joints or gluing hard-to-reach spots. Includes 2 applicators. IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™;...
$8.00

Add to Cart


Insta-Set Accelerator.

Insta-Set Accelerator.

Cure CA glue in 6 seconds. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed...
$7.00

Add to Cart


Un-Cure Debonder

Un-Cure Debonder

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and...
$4.50

Add to Cart


IC-Loc Blue Threadlocker

IC-Loc Blue Threadlocker

IC-Loc™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-Loc Blue™ is cured, the fasteners can be disassembled with standard hand tools if required.
$6.75

... more info




<